Semi-Solid Die Casting

Based on the theory of stir cast invented by Mr. D.B. Spencer and M.C.Flemings, the semi-solid die casting technic has been further developed and applied over 30 years worldwide. The main principle of the semi-solid die casting technic is to perform a strong stir during the metal phase change from liquid to solid, thus breaking the cylindrical and dendritic crystal to achieve a much smaller grain size. While this phase still maintains certain flow properties, the semi-solid metal casting could be performed on the metal.

Advantages of Semi Solid Die Casting

The advantage of semi-solid die casting is contributed from the very nice microstructure product it resulted in. As the rough big crystal was removed, leaving small, even, dense structure metal, the final products possess a number of the fine properties, and the semi solid metal casting process is more controllable as well.

Higher viscosity than liquid metal, easier to control: less gas entrained in the mold, less oxidation, improved processability, less mold bonding, higher speed part forming, improved surface finish, easy automation, and formation of new processing processes.

Lower flow stress than solid metal: semi-solid slurry has rheological and thixotropic properties, very small deformation resistance, which can form parts at higher speeds and can perform complex part forming, shorten processing cycles, improve material utilization, contribute to energy and material savings, and allow high-speed forming of continuous shapes (such as extrusion) and low processing costs.

Forming Principle of Semi Solid Die Casting

The unique rheological and churning properties of non-dendritic semi-solid metals (SSM) are used to control the quality of castings. The three stages of liquid, solid, and semi-solid metals exhibit distinct physical properties, and these properties have led to a variety of methods of solidification, plasticity, and semi-solid metal forming. Semi-solid metals (alloys) are internally characterized by the coexistence of mixed solid-liquid phases and the presence of metallic liquids at grain boundaries, which vary in the state depending on the solid phase fraction. It can be seen that at high solid phase fraction, the liquid phase component is limited to some of the grain boundaries; at low solid phase fraction, the solid phase particles are free in the liquid phase component.

Applications of Semi Solid Die Casting

Wide range of applications: all alloys with the solid-liquid two-phase area can achieve semi-solid processing, which can be applied to a variety of processing processes, such as casting, rolling, extrusion and forging, etc., and can be used for material compounding and forming.

There are many casting suppliers, but we are one of the best choices for you.

Other supplier products

	Low Pressure Die Casting	The low pressure casting machineis to let the melted metal flow into the casting mold under a certain degree of pressure, and solidify the casting ...
	Nuclear & Power Plant	Rayforce's metal nuclear castingscan be applied to heat exchange machines, boilers, economizer parts, chemical engineering casting parts, water tre...
	Investment Casting	Investment casting, also called the lost-wax casting process, is actually an ancient metal casting technology with a history of over 6,000 years. I...
	Metal Casting	Casting process usually refers to the metal casting process, is one of heating processing technologies handled by humans can be found recorded as e...
	Resin Sand Casting	Resin sand castingis a kind of floor molding process, by mixing the resin with quartz sand and solidification agent, to create the very hard and so...

供应产品

Same products

	ENGINE BRACKET/ENGINE MOUNTING BRACKET	卖方: EMP Tech Co.,Ltd	car engine mounting bracket engine bracket carwhich is divided into two parts is a component...
	ENGINE CYLINDER LOWER BLOCK	卖方: EMP Tech Co.,Ltd	The car cylinder blockis located between the engine cylinder and the oil pan. EMP Tech, as an ...
	湿砂造型线	卖方: China most professional Foundry Machinery platform	可根据铸件产品定制湿砂（湿砂）砂回收系统 粘土砂是以粘土为结合剂的型砂。 砂处理部是铸造厂的重要组成部分。 其主要任务是为造型制芯部门提供合格的型砂。 型砂的制备直接影响铸件生产质量、产量的提高...
	Sodium Silicate Sand Casting	卖方: Shanxi Rayforce Manufacture Co., Ltd.	Sodium silicate castingis soluble in water in various amounts. A more common name for sodium sili...
	Grey Cast Iron Casting	卖方: Shanxi Rayforce Manufacture Co., Ltd.	The name grey iron is because of the gray color of the fracture it forms, which is due to the pre...