Horizontal Thermal Test Chamber

• 

Application
JOEO horizontal thermal test chamber is the best choice for batch testing and large test loads. The interior design is used for custom environmental stress screening of components and board level electronic components. The carrier basket transfers loads between hot and cold zones in two - or three-zone configurations, and is widely used in automotive, electronic and electrical, aerospace, communication equipment, medical equipment and other industries.If you need more models about our test equipment, please reference our chamber-testing（.）com


Meet Standards

IEC 60068-2-14 Nc - Rapid change of temperature, two-fluid-bath method
MIL-STD-883J Method 1011.9 - Military standard, test methods for microcircuits Thermal Shock
MIL-STD-202 Method 107 - Military standard, test methods for electronic and electrical component parts Thermal Shock
JESD22-A106B - Thermal Shock
IEC 60749-11 - Semiconductor devices, Mechanical and climatic test methods Part 11: Rapid change of temperature, Two-fluid-bath method
EIAJ ED-4701/307 - Environmental and endurance test methods for semiconductor devices Thermal Shock

Description
JOEO Horizontal thermal test chamber are available in a variety of configurations and are the right solution for all thermal shock test requirements for large or batch products.

Two zones, single capacity (-2)
(One hot zone and one cold zone)
The product in the test moves through a carrying basket, alternating between hot and cold zones.

Two-zone Dual Capacity (-2D)
(Two hot zones and one cold zone)
In a two-zone, two-capacity system, the cold zone is always in use, which helps to improve system efficiency.

Three zones, single capacity (-3)
(One hot zone, one normal zone and one cold zone)
In the horizontal three zones, the product moves through the carrier basket between the cold zone and the normal temperature zone, and the hot zone moves to surround the product basket.


Feature

The reference test load of the JOEO thermal test chamber is composed of 12 steel plates. Each pound of steel has an exposed surface area of 65 square inches. The test load is oriented in the product carrier, with the airflow parallel to the steel plate. The load is distributed between two product carriers.
The weight of any additional racks must be included in the test load shown above.
The capacity depends on the stability of the product at extreme temperatures before transfer. Do not use environment dwell time.
When assisted by liquid nitrogen, smaller mechanical refrigeration systems will maintain low temperatures. Liquid nitrogen is required to meet the recovery time.
For a liquid nitrogen only thermal chambers, the maximum load is liquid nitrogen cooling without mechanical cooling.
Use IC chip product loading to recover 9 point products in 15 minutes or less. The load is distributed between two product carriers.

Другие товары поставщика

	ESS Chamber(Damp Heat Testing) With Loading	Application Suitable for testing the quality of electrical, electronic, instrument, communication, vehicle, plastic products, metal, food, chemical...
	Фирма JOEO Environmental Test Chambers производит климатические испытательные камеры	Приложение Камера влажности JOEO, камера с климат-контролем, камера моделирования окружающей среды предназначены для проверки способности к жаре, ...
	ESS Chambers-Temperature Humidity Chamber	Application JOEO ESS chambers are suitable for the whole product, parts and materials for high temperature, low temperature, high and low temperatu...
	Ozone Aging Test Chamber	Introduction JOEO ozone aging test chamber through the simulation and enhancement of ozone conditions in the atmosphere, to study the impact of ozo...
	IEC 60068 Salt Fog Chamber of Cyclic Corrosion Salt Spray Chamber	Applicable JOEO Cyclic corrosion salt spray chamber,salt spray chamber is tested the corrosion resistance capacity of products, which stay in the i...

Похожие товары

	Walk In Environmental Chamber	Продавец: Guangdong ALI Testing Equipment Co,.Ltd	Application JOEO Multi-functional walk in environmental chamber is the perfect testing place for ...
	Solid Walk In Test Chamber	Продавец: Guangdong ALI Testing Equipment Co,.Ltd	Application: JOEO solid walk in test chamber is an all-welded test chamber with an integrated con...
	Compact Walk In Environmental Chamber	Продавец: Guangdong ALI Testing Equipment Co,.Ltd	Application JOEO compact walk in environmental chamber is used to test full-size solar panels or ...
	Drying Walk In Environmental Chamber	Продавец: Guangdong ALI Testing Equipment Co,.Ltd	Application Dry walk in environmental chambers are a special type of walk in environmental chambe...
	Walk In Test Chamber For CATL Battery	Продавец: Guangdong ALI Testing Equipment Co,.Ltd	CATL Battery Walk In Test Chamber JOEO Walk In Test Chamber's temperature cyclic stress screening...